|Click on image above for a full resolution view (will open in new window).|
Our best-selling 3D printer controller, now available with Pololu Black Edition high-power stepper drivers at a new low price!
The Sanguinololu is a complete electronics solution for driving your RepRap 3D printer, whatever the type - Prusa, MendelMax, Huxley, Mendel90, Repstrap, etc. These boards are version 1.3a, the latest version with support for the latest and most feature-rich firmware - Marlin. Marlin's extra features include the use of an LCD+card-reader+click-encoder combination for true stand-alone printing (as described on our blog and available here). The display+encoder combination also allows real-time alteration and saving of firmware settings - a significant advance in usability. To access these features with the Sanguinololu requires the ATmega 1284 chip because of the extra memory required.
Our boards are professionally assembled and fully tested, and we have sold hundreds of them on eMakershop, eBay and directly in bulk to major suppliers of complete RepRap kits. We fit genuine Pololu A4988 Black Edition stepper drivers, not stepstick clones, and supply heatsinks and thermal tape for them.
For more information check out the RepRap wiki: Sanguinololu
Please note that our boards include not only the Sanguinololu but also all the female connector housings and crimp terminals, a heatsink for the heatbed MOSFET, and 3 endstops with cables - total extra value over £3.50. If you buy a board with Pololus, then we also include heatsinks for these, and thermal tape to fit them, at no extra cost.
This listing is for a 100% complete assembled solution, Sanguinololu with genuine Black Edition high-power A4988 Pololu drivers, professionally assembled, tested and guaranteed working on depatch.
The ATMEGA 1284P microprocessor comes pre-loaded with the bootloader and a standard Prusa Mendel configuration of the latest Marlin firmware, and is tested for correct operation. You can download Marlin from Github and customise it to your exact requirements using the freely available Arduino software. On request we will supply a brief HOWTO outlining the firmware upload procedure. Prusa has a good calculator for different hardware configurations here. These settings are easily changed to suit your printer configuration.
Power Connection Options
The 12V connection to the board needs to be able to carry sufficient current to run 5 motors, the hotend and a heated bed, if you choose to run one through the electronics. You can choose either to use the 4 pin ATX connector from a computer power supply or a screw terminal connection. The ATX connector is simpler if you plan to use one of these power supplies for your printer. The screw terminal is more versatile if you are not yet sure what you will use as a power supply. There is no cost difference between these two options.
IMPORTANT NOTE: WHEN PURCHASING, PLEASE ADVISE US WHICH POWER CONNECTION TYPE YOU REQUIRE, ATX OR SCREW TERMINAL. YOU CAN SEND A NOTE WITH YOUR PAYPAL PAYMENT OR EMAIL US AT THINK3DPRINT3D@GMAIL.COM.
ATX power terminal and Screw power terminal options
Assembled boards include:
Check out our other items here.
eMakershop will combine postage on multiple purchases automatically.
If we receive your order before 10:00 noon UK time Monday to Friday we aim to post the same day, otherwise the following day. Orders received later on a Friday or before 08:00 am UK time on Saturday will normally be posted on Saturday.
UK postage is by Royal Mail First Class Recorded. For postage outside the UK, we use a fully-tracked Royal Mail Airmail service where available - either AirSure or International Signed For. Fully tracked services are available to the following countries:
Austria, Belgium, Denmark, Estonia, Finland, France, Germany, Hungary, Luxembourg, Netherlands, Poland, Portugal, Republic of Ireland, Slovakia, Spain and Sweden
Non European Union Zones
Andorra, Azores, Balearic Islands, Canary Islands, Corsica, Faroe Islands, Iceland, Liechtenstein, Madeira, Monaco and Switzerland
Rest of the World
Australia, Brazil, Canada, Hong Kong, Japan, Malaysia, Singapore, New Zealand and USA
Where a fully-tracked service is not available, then we will use International Signed For (partly-tracked). If a fully tracked service is not available to your country and you want your parcel to be fully tracked, please enquire before buying. (Please write to us at email@example.com)
We have unfortunately had to exclude some European countries from this listing because of a large number of items going missing in their postal systems. If you are in one of the excluded countries and want to buy from us we will be happy to quote you for shipping by courier services. (Please write to us at firstname.lastname@example.org)
EUROPE: Albania, Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Cyprus, Macedonia, Malta, Moldova, Montenegro, Serbia, Ukraine
AFRICA: All of Africa except South Africa
This is a summary of the steps required to get up and running:
Please write to us at email@example.com if you have any queries
Think3dPrint3d is registered for VAT and all products are VAT inclusive. If you require a VAT invoice please contact us.
|First item||Subsequent items|
|National (United Kingdom)||£4.00||£2.50|
|Rest of the world||£10.00||£2.50|